Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Suspension

Enduro Suspension Tuning & maintenance of Enduro forks, shocks, etc


Reply
 
Thread Tools Display Modes
  #1  
Old 12-07-2006, 12:32 PM
Dingoe Dingoe is offline
Member
 
Join Date: Nov 2006
Posts: 17
Default Bearing kit cross???

Does anyone know what swing arm and linkage bearing kits cross with the Gas Gas 2s.

Mine looks old dry and a bit pitted, but I'll sand clean and repack and hope to get by. If I need them I'd like to get full kits at a good price. I'm runnning out of funds working on the bike.

thanks


Reply With Quote


  #2  
Old 12-11-2006, 05:21 PM
wheels7 wheels7 is offline
Member
 
Join Date: Nov 2006
Posts: 22
Default linkage and swingarm kit

moose racing has a kit for the gas gas bikes i have my kit for my 300 i just need to put it in. but i cant figure out how to get the swingarm bolt out?
Reply With Quote
  #3  
Old 12-11-2006, 06:57 PM
wheels7 wheels7 is offline
Member
 
Join Date: Nov 2006
Posts: 22
Default

http://cgi.ebay.com/ebaymotors/REAR-...62669801QQrdZ1
there you go
Reply With Quote
  #4  
Old 12-12-2006, 04:06 PM
Dingoe Dingoe is offline
Member
 
Join Date: Nov 2006
Posts: 17
Default

Thanks for the info, on the swingarm bolt, I pulled my linkage and arm from the frame with the help of WD-40 and MR. Hammer. Water did a number on it, but it's out and it's clean now. Get a long 3/8" extention and drive it out, make sure the right side is free of rust, dirt , etc.
Reply With Quote
  #5  
Old 12-14-2006, 11:23 PM
Boomhauer's Avatar
Boomhauer Boomhauer is offline
Senior Member
 
Join Date: Sep 2006
Posts: 920
Default

Quote:
Originally Posted by wheels7 View Post
moose racing has a kit for the gas gas bikes i have my kit for my 300 i just need to put it in. but i cant figure out how to get the swingarm bolt out?

Leave the nut on the end of the bolt and un thread it so slightly and use a punch and a hammer. GENTLY tap on the nut until the bolt starts to move and repeat the process.

The nut is on the driver side (left side) of the bike. The bolt will then push out thru the right side.

Also when I put mine back together I always fill the swing arm bolt cavities with grease to keep out dirt and water. I have had no problems doing this.

Good Luck!
__________________
Bikeless for Now
Thanks to Smith's Powersports 724-899-3375
www.smithspowersports.com
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Air Filter Cross Over ?'s lordfeyr Enduro Intake/Carburetion - 2 stroke 11 02-25-2011 12:00 PM
Big End Bearing twistywizard Enduro Engine - 2 stroke 15 01-26-2011 07:33 PM
reeds cross-over? moff747 Enduro Intake/Carburetion - 2 stroke 4 05-25-2010 03:32 AM
Wrist Pin Bearing SpeedyManiac Enduro Engine - 2 stroke 16 10-08-2009 10:37 PM
lower shock bearing cross-ref? fasternat Enduro Suspension 1 02-21-2007 11:20 AM




All times are GMT -5. The time now is 04:23 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org