|
Enduro Chassis & Body Enduro Frame, Plastic, Brakes, Bars, Controls, wheels, tires, sprockets & gearing. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Torque setting for steering head nut?
Anyone know the Torque setting for steering head nut on top of the triple clamps? 2013 300r, but I assume they are all the same?
Not good when your wiping off WD-40 and it spins loose |
#2
|
||||
|
||||
The torque table is here:
__________________
2004 GasGas DE250 |
#3
|
|||
|
|||
Thanks mate, that'll do it. For future reference it is a 30mm nut, the table has "20?".
|
#4
|
||||
|
||||
20mm is the 'bolt' size, for instance standard fitting on a 6mm bolt is a 10mm wrench........
__________________
Fred Overstreet 2010 EC250 SixDays 2004 GasGas EC300 -Sold to a good home 2006 GasGas EC250-Sold to a good home 2006 GasGas TXT 280 Pro |
#5
|
||||
|
||||
I personally just tighten up the lock nut until everything is snug, then back it off finger tight. Use a 1/2 driver with the 30mm socket and do it up until its tight. 20Nm isn't much at all.
Last edited by Jakobi; 10-23-2013 at 06:56 PM. Reason: Misleading information removed. |
#6
|
|||
|
|||
Quote:
__________________
"Conviction is a luxury of those on the sidelines." '13 Beta 300RR - race bike '02 GG300XC - "Billie Baroo" '01 DR650 '02 GG 280 Pro '06 YZ 250 '07 WR450 '00 TT125RL '94 YZ200 - custom keeper |
#7
|
||||
|
||||
Quote:
Do you not have an owner's manual for your 2013 300r. http://www.gasgasmotos.es/en/manuals.html Per the manual it says 20 Nm
__________________
2012 - XC 300 Racing Seattle, WA |
#8
|
|||
|
|||
Quote:
Thanks Jake, I don't normally use torque numbers, so your I'll just take your advice and check it after the first ride. My mate had to use a 2 foot breaker bar to loosen the one off his TM300 from the factory, so glad I didn't use his 'advice'. |
#9
|
||||
|
||||
Read my post again - sorry I was not trying to be such a jerk about that. Sorry
It depends on which manual you use. I use the 2013 Factory Replica Manual as it is the most current one.
__________________
2012 - XC 300 Racing Seattle, WA |
#10
|
|||
|
|||
All good - i'll just use the 'torque it till you think it's tight enough' method i think.
Cheers |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Steering head bearings | Cberg | Enduro Chassis & Body | 9 | 10-20-2012 10:52 PM |
Steering stem nut torque | r00zter | Enduro Suspension | 9 | 08-04-2012 07:10 AM |
Setting new cylinder studs - torque | motogroove | Enduro Engine - 2 stroke | 3 | 07-20-2011 02:04 AM |
Torque cylinder head EC 300 2009 | Klausen | Enduro Engine - 2 stroke | 9 | 10-03-2010 10:49 AM |
Front axle bolts Torque setting | biggstr6 | General Discussions & Announcements | 6 | 04-23-2010 08:01 AM |