Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Engine - 2 stroke

Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 09-19-2010, 03:23 AM
Klausen Klausen is offline
Senior Member
 
Join Date: Nov 2009
Location: Germany
Posts: 136
Default Torque cylinder head EC 300 2009

I want to change the piston.
Is there anywhere are repair manual in the net for a 2009 EC 300 gasser.
thanks


__________________
Husqvarna TE 300
Reply With Quote


  #2  
Old 09-19-2010, 06:09 AM
GMP's Avatar
GMP GMP is offline
Senior Member
 
Join Date: Jul 2006
Location: Jefferson Twp., NJ
Posts: 7,597
Default

25Nm, OR, subtract approx 20% for antiseized threads so approx 20Nm. Motor has been the same for years so older manual should apply.
Reply With Quote
  #3  
Old 09-19-2010, 09:58 AM
Klausen Klausen is offline
Senior Member
 
Join Date: Nov 2009
Location: Germany
Posts: 136
Default

thanks this 25Nm I found in the owner manual
But where can I find a service manual for the engine.
__________________
Husqvarna TE 300
Reply With Quote
  #4  
Old 09-21-2010, 03:13 AM
Klausen Klausen is offline
Senior Member
 
Join Date: Nov 2009
Location: Germany
Posts: 136
Default

Quote:
Motor has been the same for years so older manual should apply.
Where can I find a manual at all.
Nobody in GG forum have one?
__________________
Husqvarna TE 300
Reply With Quote
  #5  
Old 09-21-2010, 04:17 AM
eff's Avatar
eff eff is offline
Silver Level Site Supporter
 
Join Date: Jul 2006
Location: RI
Posts: 1,758
Default

Here it is:

http://www.gasgasrider.org/torque_table.jpg
__________________
2004 GasGas DE250
Reply With Quote
  #6  
Old 09-21-2010, 05:02 AM
Klausen Klausen is offline
Senior Member
 
Join Date: Nov 2009
Location: Germany
Posts: 136
Default

Where can I find wear limit for clutch and piston
__________________
Husqvarna TE 300
Reply With Quote
  #7  
Old 09-21-2010, 05:08 AM
GMP's Avatar
GMP GMP is offline
Senior Member
 
Join Date: Jul 2006
Location: Jefferson Twp., NJ
Posts: 7,597
Default

I havn't looked lately, are the shop manuals still available for download on the GG Spain site? If not, I can email you a copy. The manual is a few years old but the engine is basically the same. That torque table I did ten years ago when I got my '00 XC250! Wow, due for a revision I'd say. A few fasteners on the new bikes are different but most apply.

Edit: I sent you a copy of the '06 service manual.
Reply With Quote
  #8  
Old 09-21-2010, 11:29 AM
Klausen Klausen is offline
Senior Member
 
Join Date: Nov 2009
Location: Germany
Posts: 136
Default

thank thats nice
__________________
Husqvarna TE 300
Reply With Quote
  #9  
Old 10-03-2010, 10:12 AM
Klausen Klausen is offline
Senior Member
 
Join Date: Nov 2009
Location: Germany
Posts: 136
Default

What is the right position of the float,
I can't find something in the repair manual.
__________________
Husqvarna TE 300
Reply With Quote
  #10  
Old 10-03-2010, 10:49 AM
GMP's Avatar
GMP GMP is offline
Senior Member
 
Join Date: Jul 2006
Location: Jefferson Twp., NJ
Posts: 7,597
Default

See the Sticky in the Intake/Carb forum.
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Cylinder Bolt Torque? eff Enduro Engine - 2 stroke 12 03-30-2008 08:44 AM
EC300 Cylinder Head Marcão Enduro Engine - 2 stroke 3 06-11-2007 03:52 PM
New cylinder head Kent A Enduro Engine - 2 stroke 8 05-01-2007 01:43 PM




All times are GMT -5. The time now is 04:56 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org