|
Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc. |
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
300 running issues
Hi guys
A friend has just brought a 300 57plate, it's got what I believe is a fuelling issues, the problem is 1st & 2nd it won't rev out. 3rd upwards it's about to come on the PV and it splutters horrible once passed it pulls well. The PV is set ok and not seized. Has anyone suffered from this, and what did you do to solve the issue? It feels like mid range fuelling,so I think a needle problem. Thx in advance Jon |
#2
|
|||
|
|||
This sounds dumb, but have you pulled the air filter and cleaned it? A long time ago I had a buddy who cleaned his filter but left a rag in the airbox, and it had the same issues.
__________________
2011 GG EC 300E, 1994 CR 250R, 1984 RM 250 E, 2022 Ranger 300 "If you stop eating donuts you will live 3 years longer. It's just 3 more years that you want a donut." ―Comedian Lewis Black "I think best when I have a wrench in my hands." Soichiro Honda "Dreams are messages from the deep." -Unknown Sardaukar |
#3
|
|||
|
|||
hi mate
Plug,, cap could be reeds, blocked carb, crap in the tank bad earth, coil, cdi clean the carb and check nothing has come loose ie jets then pull the reeds as some times the corner breaks off. start with the easy stuff and what's not going to cost as it may be a simple fix then change the plug even if its a old known working one check and clean the wiring connections and clean the earth, I would put some oil on them like wd40 if nout change the coil and worst get the cdi checked hope this helps
__________________
03 ec300 honda cr500 94 |
#4
|
|||
|
|||
Hi
Yep air box is ok. Carb stripped and checked, new plug and cap, earths seem ok but will check with a meter. Going to a dyno next week to check the fuelling, see what that shows |
#5
|
|||
|
|||
Check the silencer sounds like a blocked spark arrester. Just had this problem I have the Leo Vince silencer and the spark arrester screen was plugged. My bike ran the same as yours.
|
#6
|
|||
|
|||
I've got the same problem with my 09 300 nambo. Only had it a week so hardly started work on it yet. It will be interesting to see how you get on.
Good luck. |
#7
|
|||
|
|||
Quote:
Removed screen and just fine
__________________
2014 Sherco SEF 300-R 2014 Sherco ST 300 2013 Sherco X-ride |
#8
|
|||
|
|||
Hmmmm. Opened up my exhaust and it was fine, so don't think that is the cause for me. The air filter was less than spotless though. Clean now and ready to try at the weekend.
|
#9
|
|||
|
|||
Have you check reeds allready?
Sent from Razr MAXX
__________________
plated 300EC 2008 |
#10
|
|||
|
|||
Currently an NEDJ
Previously a N1EF Fault the same for both. It happens at WOT only so I'm thinking the needle may have less of an influence. The chap at Gas Gas UK said the silkolene oil I was using was bad for gumming so maybe I'll go through the pv again. Also the exhaust. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Ec250 running issues | jimgsxr86 | Enduro Engine - 2 stroke | 9 | 05-03-2013 05:52 PM |
06-300 not running | davedunaway | Enduro Electrical & Wiring | 11 | 08-29-2012 09:21 AM |
03 300 not running | tophat | General Discussions & Announcements | 22 | 08-23-2011 03:51 AM |
Running hot | Brian VT | Enduro Engine - 2 stroke | 9 | 10-01-2008 07:25 AM |
Running In | Dingo | Enduro Engine - 2 stroke | 3 | 07-26-2007 11:36 PM |