|
General Discussions & Announcements General Announcements, General Questions, e.g. What bike do I buy?, etc. |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
Frustration ^2
I got my gaskets yesterday, 13 days after I ordered them.
Many of them are wrong - either wrong bike or wrong place on my bike. Water outlet gasket is way too big (I ordered two, great). Maybe a later model bike, or just plain wrong bike... I dunno. It's not like I didn't say that everything was for a 2001 xc300 Center crankcase gasket that I didn't order. Who knows if that's correct for a 2001. Always something extra that I didn't order from this vendor too. Base gaskets look funny compared to the circa 2001 gasket I used a few months ago. Not sure about that... I'll know later today The boys are riding this weekend. Will I be there? It's not looking good, unless I blow off work so I can play parts detective and then buy overnight shipping. -Dean missing the season trying a new vendor
__________________
Thanks to FLY Racing. Last edited by motogroove; 07-14-2011 at 07:24 AM. Reason: inlet, outlet... |
#2
|
||||
|
||||
Well, are you going to tell us where you ordered them from???
__________________
Alan 14GasGas ec300r |
#3
|
||||
|
||||
I hate to throw <anybody> under the bus.
<clue deleted>
__________________
Thanks to FLY Racing. Last edited by motogroove; 07-16-2011 at 07:09 AM. Reason: vendor's honest effort to fix the problem |
#4
|
|||
|
|||
Sure its not Bob and North Tahoe. I can think of few clueless vendors in my neck of the woods.
|
#5
|
||||
|
||||
Just deal with Smith's Powersports in Imperial PA, or Hall's. They both stock a lot and know the bikes, excellent dealers. I have had some screw ups myself from other vendors in the past, I attributed it to cheap summer help that did not give a crap.
|
#6
|
||||
|
||||
i'm assuming you mean the water outlet on the cylinder head? there are several different ones.... i just make mine, a sheet of gasket paper, a set of punches and an exacto have fixed many last minute problems......
there are 3 different thicknesses of base gasket.. i believe they're all the same aside from thickness....
__________________
07 ec300 was 00 xc200 now a 00 xc300. now parting out. 99 ec300 (now a pile of parts which are for sale) Stainless Cycle - Motorcycle Bolt Kits www.stainlesscycle.com |
#7
|
||||
|
||||
Quote:
Yes, that's the gasket. And I made the last two myself also. I just was trying to make the order worth everybody's time. And I never mind having the details look correct. In a case where there are several different this or that, I would help the customer determine which one is the desired item. I wouldn't have worried about the thickness of the base gasket until I wandered into this nut-house. A little knowledge is a dangerous thing. Anybody know what the three thicknesses are? These are looking like ~0.59mm ? (one is just a spare, I'm not starting stacking and carving). Thanks again to the vendor for getting on top of it.
__________________
Thanks to FLY Racing. |
#8
|
||||
|
||||
OK, these are called .5mm. Maybe they crush down to that when installed. The others are .3 and .15mm.
__________________
Thanks to FLY Racing. |
#9
|
|||
|
|||
the three sizes of base gaskets allow you to fine tune your compression/port timing in your motor. hopefully someone more knowledgeable than me will chime in and let you know what a good baseline setup is.
|
#10
|
||||
|
||||
[QUOTE=stainlesscycle;66825]i'm assuming you mean the water outlet on the cylinder head? there are several different ones.... i just make mine, a sheet of gasket paper, a set of punches and an exacto have fixed many last minute problems......
[QUOTE] Here are two of the water outlet variations. My 2001 bike's head uses the smaller one, which I was told began in 2003. Make note which one you have and be specific wherever you order. -Dean always ahead of my time hey, that's a pun
__________________
Thanks to FLY Racing. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
03 GasGas 450FSE Frustration | ktownrider | Enduro Engine 4 stroke (including EFI & Exhaust) | 9 | 12-20-2007 11:11 AM |