Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > GasGas Enduro Technical Forums > Enduro Electrical & Wiring

Enduro Electrical & Wiring Lighting, Ignition, Wiring, Plugs, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 06-20-2013, 06:18 AM
motopsycho87 motopsycho87 is offline
Senior Member
 
Join Date: Jun 2013
Location: Suffolk, UK
Posts: 905
Default Sputters at high revs...

... Hi guys, recently bought a EC300 2006. It ran fine until I pressure washed it, I rode it straight away afterwards and from then it refused to give me high revs.

I have an ignition coil and HT cap on order, spark plug is brand new, just wanna know if you guys can think of anything else that might have happened ? Common faults perhaps?
Reply With Quote
  #2  
Old 06-20-2013, 07:09 AM
pscook's Avatar
pscook pscook is offline
Platinum Level Site Supporter
 
Join Date: Oct 2011
Location: Shoreline, WA
Posts: 1,164
Default

There was a thread yesterday or day before where GMP explained that the HT lead from the stator to the coil can get contaminated with water and cause running issues. You may want to pop the seat and tank and check every temporary (spade and bullet) connection and apply some silicone grease to the connections.
__________________
Phil
(New bike pending...)
Reply With Quote
  #3  
Old 06-20-2013, 08:51 AM
motopsycho87 motopsycho87 is offline
Senior Member
 
Join Date: Jun 2013
Location: Suffolk, UK
Posts: 905
Default

Yeah , I've ordered and am gonna change all that anyway. CBA to chase my tail looking for something when it's a ?20 fix.
Reply With Quote
  #4  
Old 06-20-2013, 06:34 PM
noobi's Avatar
noobi noobi is offline
Senior Member
 
Join Date: Sep 2008
Location: New Zealand
Posts: 1,031
Default

I wouldn't recommend riding the bike right after washing it, unless you take the filter out and seal the airboot.
The filter always manages to get damp somehow, and riding the bike sucks moisture into the engine, which isn't where you want it.

Might be superstition but heard it from more than one bike mechanic.
Reply With Quote
  #5  
Old 06-21-2013, 04:24 AM
swazi_matt swazi_matt is offline
Senior Member
 
Join Date: May 2010
Location: From Swaziland, Now Hamilton New Zealand the “look but don’t touch” enduro heaven
Posts: 2,336
Default

riding after a wash is something that has become fashionable due to the newer pumpkins having a(nother?) design flaw that supposedly allows water from washing to run into the engine and rust the big end bearing (according to local KTM dealers anyway)

All you need to do with a GG is wash it then remove the exhaust plug and spray a bit of WD40 on the chain and other parts that you do not want to have water sitting in
__________________
2003 txt250 Pro
2013 Ossa 280i
Reply With Quote
  #6  
Old 06-21-2013, 05:10 AM
Jakobi's Avatar
Jakobi Jakobi is offline
Super Moderator
 
Join Date: Oct 2010
Location: Australia
Posts: 7,992
Default

I always make sure the piston is at tdc for washing, and then plug it. Afterwards I always start it and bring it up to temp. Maybe a bit of moisture gets pulled through, but you'd imagine running it up to temp would also be enough to remove anything internally. It evaporates the water off the outside so I assume the same would happen inside..
Reply With Quote
  #7  
Old 06-21-2013, 10:12 PM
GMP's Avatar
GMP GMP is offline
Senior Member
 
Join Date: Jul 2006
Location: Jefferson Twp., NJ
Posts: 7,601
Default

HV wire loose in coil body, lets moisture in. Put your hand on the coil or wire when it's running, get a shock? I've had this happen on three bikes over time.


Sent from my iPad using Tapatalk HD
Reply With Quote
Reply




Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Power drops with revs swazi_matt Enduro Electrical & Wiring 0 10-09-2011 05:52 AM
New 2010 EC300 Engine Noise (falling revs) Jakobi Enduro Engine - 2 stroke 11 11-16-2010 06:41 PM
Max revs when starting up. Todd5774 Enduro Intake/Carburetion - 2 stroke 4 01-24-2010 08:22 AM
EC300 Revs when cold-started stevethebrit Enduro Intake/Carburetion - 2 stroke 6 07-10-2009 11:04 PM
Revs from hell -- stuck throttle or bad mojo? AZRickD Enduro Intake/Carburetion - 2 stroke 25 01-21-2009 08:54 PM




All times are GMT -5. The time now is 10:18 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org