Rieju & GasGas Legacy Riders Club Forum  

Go Back   Rieju & GasGas Legacy Riders Club Forum > General Forums > General Discussions & Announcements

General Discussions & Announcements General Announcements, General Questions, e.g. What bike do I buy?, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 01-17-2013, 09:25 AM
Steve Croxton Steve Croxton is offline
Member
 
Join Date: Oct 2012
Posts: 21
Default 2012 Parts crossover

Is there one? If so where can I find it?

Thanks


Reply With Quote


  #2  
Old 01-17-2013, 01:33 PM
hannesd hannesd is offline
Senior Member
 
Join Date: Jun 2010
Location: belgium,europe
Posts: 546
Default

http://www.gasgasrider.org/html/parts_crossover.html

there you go
Reply With Quote
  #3  
Old 01-17-2013, 02:19 PM
noobi's Avatar
noobi noobi is offline
Senior Member
 
Join Date: Sep 2008
Location: New Zealand
Posts: 1,031
Default

What parts are you trying to crossover?

The engine has been the same for a long time.
The chassis and plastic are new 2012, they changed again slightly in 2013.
The e start stuff should crossover to the 2011 e start system.
Suspension changed with the chassis in 2012, linkage changed again(?) in 2013.

Wheels should cross between most years, air filters are 07+ I believe.

Brake pads are off a YZ, I think the numbers are 126 and 326, front and rear respectively.
Reply With Quote
  #4  
Old 01-20-2013, 07:34 PM
Steve Croxton Steve Croxton is offline
Member
 
Join Date: Oct 2012
Posts: 21
Default

I'm trying to find out what holeshot/launch device will fit front fork guards.Thanks.
Reply With Quote
  #5  
Old 01-20-2013, 10:57 PM
noobi's Avatar
noobi noobi is offline
Senior Member
 
Join Date: Sep 2008
Location: New Zealand
Posts: 1,031
Default

Quote:
Originally Posted by Steve Croxton View Post
I'm trying to find out what holeshot/launch device will fit front fork guards.Thanks.
Can you not buy just the button and bracket and fit it to the guard yourself? Allowing you to set the height to what you want.

However, CR fork guards have the same bolt pattern, well at least they have previously. KTM ones will work too apparently but I haven't tested that one.
Reply With Quote
  #6  
Old 01-23-2013, 09:00 PM
Steve Croxton Steve Croxton is offline
Member
 
Join Date: Oct 2012
Posts: 21
Default

Yes, but the fork guards on my bike have a ridge in the center right where the button for the launch device would mount, all others(ktm, honda ect.) I've looked at are round and smooth. Does anyone know if there is a brand that has a ridge like the GASGAS?
Thanks
Reply With Quote
  #7  
Old 01-23-2013, 11:03 PM
desertgasser300 desertgasser300 is offline
Banned
 
Join Date: Feb 2011
Location: Hot A@% desert AZ.
Posts: 1,872
Default

Polisport has the ridge. It is the same fit as ktm and some crf's
Just bought a pair for a set of zoke 45's.
Reply With Quote
  #8  
Old 01-24-2013, 01:17 AM
twowheels's Avatar
twowheels twowheels is offline
Senior Member
 
Join Date: Oct 2009
Location: Dearborn MI
Posts: 1,860
Default

The OE GasGas fork guards can be split and removed from the forks without taking the wheel off. The KTMs have the same wrap but not the split (iirc). The Hondas don't have a back and less coverage (again iirc).
__________________
Steven Beane #275
PlusOnePerformance - Superior Service the World Over - Dearborn MI
AMA District 14 (Michigan) Officer

afterhourscycle.com
Michigan's Beta and TM Race Headquarters
Reply With Quote
  #9  
Old 01-24-2013, 10:19 AM
desertgasser300 desertgasser300 is offline
Banned
 
Join Date: Feb 2011
Location: Hot A@% desert AZ.
Posts: 1,872
Default

To find what would fit the forks I went to the Polisport website and compared part numbers, ie GasGas/KTM/CRF all had the same part number. Then just order from the least expensive website and wait.

Sorry Steve I do cheat once in awhile!
Reply With Quote
  #10  
Old 01-24-2013, 04:40 PM
robszombie's Avatar
robszombie robszombie is offline
Member
 
Join Date: May 2009
Location: Meath, Ireland
Posts: 71
Default

Still no luck sourcing a 2012 aftermarket brake pedal. I hope someone builds one soon. If i break/bend this third one I'll have to go back to the 2011 model!!!!!
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Another Parts Crossover Question carlg Enduro Chassis & Body 1 11-28-2010 11:37 PM
EC200 parts crossover rupecopp Enduro Other... 7 10-20-2008 08:27 PM
4-stroke parts crossover Motarded1 Enduro Engine 4 stroke (including EFI & Exhaust) 4 11-05-2007 01:07 PM
MC65 parts crossover? bergerhag General Discussions & Announcements 5 10-07-2007 09:16 AM
Parts Crossover idea Phattaff Suggestion Box 3 08-21-2006 05:43 PM




All times are GMT -5. The time now is 02:38 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org