|
Enduro Intake/Carburetion - 2 stroke Jetting, Reeds, Air Filters, etc. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
'06 ec300
I was looking through the data base here and though there was alot of heplful tips Idid not find the combo of jetting and clip setting I was looking for.So my question is what is the best set-up for 0 to 1500 50 to 70 degrees,a CCK needle and a #8 slide and VF3 Reeds? Now 1nee top slot,172 and 40 and #7 slide fuel 1 1/4turn and spooges out of the pipe but not bad but could be better!
Thanks. |
#2
|
|||
|
|||
I would start with a CCK needle #3 clip, #7 slide, 40 pilot and 175 main. Then tune from there.
__________________
Eric K '06 GasGas EC300 '01 GasGas XC300 |
#3
|
|||
|
|||
Thanks,
Did I waste my money on a #8 slide!Or could I use it with no ill effects? |
#4
|
||||
|
||||
Slide cutaway has a similar effect as needle diameter. The #8 slide will be more lean than the #7 slide.
__________________
Matt Current: 2009 Yamaha FZ1 Previous: 2001 GasGas TXT280, 2001 GasGas XC250, 2004 KTM 200EXC, 2007 GasGas EC250, 2007 Husqvarna SM610, 2008 Husqvarna WB165 |
#5
|
|||
|
|||
I can't recall where I heard or read it,but I was fishing for that combo of settings that included the #8 slide that was tried and tested.I guess I am looking for that solid base from wich to start from.That is whats great about this forum!
|
#6
|
|||
|
|||
My '06 EC300 works noticeably better with the #7 slide. The #8 slide was less consistent across temp and elevation changes.
My '01 clearly runs better with a #8 slide. Your mileage/results may vary.
__________________
Eric K '06 GasGas EC300 '01 GasGas XC300 |
#7
|
||||
|
||||
Quote:
http://www.gasgasrider.org/forum/showthread.php?t=1414
__________________
Matt Current: 2009 Yamaha FZ1 Previous: 2001 GasGas TXT280, 2001 GasGas XC250, 2004 KTM 200EXC, 2007 GasGas EC250, 2007 Husqvarna SM610, 2008 Husqvarna WB165 |
#8
|
||||
|
||||
I love #8 slide in my 2000 EC300 with the LTR needle. I also liked it in my 2005 EC300 until I got the RB head and then I needed to tame the bike a little. This is when I switched to the CCK needle, the stock #7 slide and dropped a tooth on the rear sprocket. Now that traction is good, I will either switch back to the #8 slide or try a CCL needle. I can use the extra pop off the bottom.
__________________
Mike Baxter 2005 GasGas EC300 (Ohlins front and rear) 2007 Yamaha FZ1 2003 Pampera 280(hers) |
#9
|
|||
|
|||
I have an EC 250 '08 with LTR and #8 slide. Before I had the #7 slide and the bike was o.k. but with the #8 it simply rips. Try it, it gives excellent response.
My winter setting are 182 main, 48 pilot, LTR#3, summer I go down to a 45 pj.
__________________
EC250 2008 Skid plate, rad braces, Fork bleeders Drz 400 Motard '03 (full spec) Yz 250 '06, KTM exc 250 '05, exc 250 '04, exc 250 '02 WRF250 '02, KDX 220 '98, DT200R '93 all sold |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
2005 EC300 vs 2007 EC300 | alecsstefan | Enduro Engine - 2 stroke | 19 | 01-22-2010 01:40 AM |