GasGas Riders Club Forum  

Go Back   GasGas Riders Club Forum > GasGas Enduro Technical Forums > Enduro Engine - 2 stroke

Enduro Engine - 2 stroke Cylinder, Piston, Tranny, Bearings, Clutch, Pipes & Silencers, etc.


Reply
 
Thread Tools Display Modes
  #1  
Old 02-22-2008, 07:42 AM
steve steve is offline
Senior Member
 
Join Date: Jan 2008
Posts: 114
Default Torque Specs

Are the torque specs for the head and jug on the links for this web site accurate? If not could someone give them to me?Thanks.


Reply With Quote


  #2  
Old 02-22-2008, 07:50 AM
eff's Avatar
eff eff is offline
Silver Level Site Supporter
 
Join Date: Jul 2006
Location: RI
Posts: 1,757
Default

It's located on this page: http://www.gasgasrider.org/html/manuals__etc.html

Reply With Quote
  #3  
Old 02-22-2008, 05:49 PM
PEB PEB is offline
Senior Member
 
Join Date: Aug 2006
Posts: 1,150
Default

Be sure to retorque the head and jug fasteners after a couple heat cycles. I didn't last time and sucked the base gasket out of alingment.

Paul B
Reply With Quote
  #4  
Old 02-22-2008, 09:57 PM
jyellard jyellard is offline
Senior Member
 
Join Date: Nov 2007
Location: Newburgh, IN
Posts: 112
Default

Do you think the head and jug fasteners should be retightened on a new bike after a few heat cycles, or only after a new top end.

Also, are the above torque values applicable to lubricated fasteners or unlubricated fasteners?

I always lube the bolts on my bikes especially since so many connections involve dissimilar metals (steel and aluminum).
Reply With Quote
  #5  
Old 02-23-2008, 06:42 PM
PEB PEB is offline
Senior Member
 
Join Date: Aug 2006
Posts: 1,150
Default

I don't know about the new bikes, I have never owned one(poor me).
Reply With Quote
  #6  
Old 02-26-2008, 08:26 AM
oldgoat oldgoat is offline
Member
 
Join Date: Jul 2007
Posts: 26
Default

( quote) Also, are the above torque values applicable to lubricated fasteners or unlubricated fasteners?

I'm almost 100% sure its for unlubricated nuts and bolts.
Reply With Quote
  #7  
Old 02-26-2008, 01:42 PM
GMP's Avatar
GMP GMP is offline
Senior Member
 
Join Date: Jul 2006
Location: Jefferson Twp., NJ
Posts: 7,597
Default

I generated that XL sheet eight years ago, probably time for an update. What seemed excessive in the GG manual was corrected with industry standard values for the relative fastener sizes and materials. No specs so assume dry fasteners. With Antiseize you can knock off up to 30% I beleive. Thats why I said elsewhere go lower on the T-clamp torque, as the bolts should be antiseized.
Reply With Quote
  #8  
Old 02-26-2008, 07:52 PM
jyellard jyellard is offline
Senior Member
 
Join Date: Nov 2007
Location: Newburgh, IN
Posts: 112
Default

Yeah, after greasing the lower triple clamp bolts and torqueing them to the specs in the chart the forks seemed a little sticky. I backed them off a little, and the fork action improved.

I'll take 30% off for the lube. Thanks.
Reply With Quote
  #9  
Old 02-26-2008, 09:30 PM
GMP's Avatar
GMP GMP is offline
Senior Member
 
Join Date: Jul 2006
Location: Jefferson Twp., NJ
Posts: 7,597
Default

I'm down to 8 - 10Nm on the GG lower clamp with antiseized bolts.
Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
05 De 300 Specs VORMAN Enduro Electrical & Wiring 9 11-14-2010 06:36 PM
Top End Clearances/Specs SpeedyManiac Enduro Engine - 2 stroke 4 09-24-2009 09:53 PM
rake and trail specs widebear Enduro Chassis & Body 9 01-28-2009 05:52 PM
ring gap specs jostby Enduro Engine - 2 stroke 9 10-27-2008 06:18 PM
Chain and Sprocket specs gasIdaho Enduro Chassis & Body 7 09-01-2006 04:03 AM




All times are GMT -5. The time now is 05:20 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org